Access Control Kit 4 is a key fob access control system with fail secure lock release, exit button, power supply and key fob door reader for standard fob access control requirements
Access control for home, access control for office or any other access control solution required

** The fail secure lock release requires power to unlock, therefore it is not recommended for connection to a fire alarm as continued power to the lock release will cause irreparable damage to the lock release coil. Connection to a fire alarm would require a fail open lock release accompanied with a green emergency break switch which are an optional choice available when ordering this access control system

Both fail secure & fail safe lock releases are compatible with a typical Yale or similar rim or mortice latch which you will require. They are not compatible with a deadlock locking device

Connection drawings

SR2-X manual


Lock Release
Lock style: Fail locked (Power required to un-lock)
12v ac/dc Coil impedance: 30 ohms
Current consumption: 760ma - 900ma
Holding force: 300kg
Supplied with: Both mortice and surface mounted face plates
Size: 160h x 25w x 31d mm

Exit button
Surface mounted plastic exit button
Single gang surface mount
Changeover contacts (C/NO/NC)
Size: 85w x 85w mm

SR2-X Proximity card reader
Compact, weather resistant multi-function card reader that can be used as a self-contained programmable access control card reader providing proximity entry for up to 1000 users, (987 common users, 2 panic users, 10 visitor users & 1 x Authorized user) or as a standalone Wiegand output card reader for PC based access control systems
PIN access is also possible via the remote control unit for the Administrator and all user data can be transferred from one unit to another within 3 minutes (Maximum connection is 9 units)

Main features
Manual and remote control programming
Epoxy resin filled for enhanced weather protection
ABS plastic body
IP rating: IP66, weather resistant
LED x 3 indication
Colour: Black
Voltage: 9-18v DC input
Current: 40mA
Reading range: 20mm - 60mm
Card type: EM Wiegand or Mifare Classic cards and/or key fobs
Card capacity: 1,000
Relay outputs: 1 x 2amp with N.C and N.O contacts
Wiegand output: Yes
Exit button input: Yes
Cable tail size: 430 mm
Fitting: Surface mount
Unit size: 103h x 48w x 20d mm
Remote control size: 85h x 32w x 5d mm

A) All features are manual or remote programmable
B) Non-volatile memory in the event of a power failure
C) 3 x LED display indication status

Power supply
Ivory white cabinet (Small)
Switch mode 13.8 volt dc regulated output 1amp power supply
Additional battery charging output
Battery deep discharge protection (Electronic)
LED Indication for mains input, DC output & battery charge/low charge
Multiple cable entry point
Size of power supply: 225h x 195w x 75d mm

Is the lock release for external use?
If in direct line of rain then no, the lock connections must be concealed to avoid weather damage

Can I use the SR2-X card reader outside?
Yes, it is IP66 rated and totally protected against dust and protection against heavy seas, or powerful jets of water

Will the SR2-X card reader use any standard Wiegand RFID 125Khz or Mifare Classic 13.56Mhz card or key fob?
Yes it can use either

Do you program cards or key fobs via the SR2-X card reader?
Yes, it's so simple to do. The SR2-X card reader is supplied with a Master Add/Delete card for this. It's also supplied with a remote control which is ideal for the deletion of lost or missing cards or fobs
NB: It is advisable to make a note of the Unique ID (U.I.D) 10 digit number printed on the cards or fobs

What happens if I lose the Master Add/Delete cards?
Don't panic!, but you will need to reset the SR2-X card reader to replace them. You can use any cards or key fobs you like to create a new Master Add/Delete card. You will not lose any previously programmed cards or fobs by resetting the unit - The reset procedure is detailed within the online manual

How do I delete cards or key fobs if I have lost them?
You can delete cards or key fobs in two ways, the first is by physically having the card or key fob and use the Master Add/Delete card, or if you have lost the card or fob, you can use the remote control by entering the U.I.D 10 digit number

Can I use two SR2-X card readers to access and exit a door?
Yes if you wish, just buy an additional SR2-X Here

If I wanted two SR2-X card readers, can I program the same card or key fob to activate both units?
Yes, you can actually connect up to 9 x SR2-X's together and upload the user information from the first SR2-X to all additional SR2-X readers. Please refer to page 7 of the manual we have for download that will show you this

Can I operate my automatic gate with this?
Yes, please refer to the drawings we have for download that will show you this

What cable do I need?
You can use any cable you like for this, we suggest using 3 paired or 4 paired standard alarm cable that you can purchase from any local electrical or DIY store

1 x SR2-X card reader, Master Add/Delete card and remote control

10 x EM-RFID blue key fobs

1 x PB1 plastic exit button (surface mounted)

1 x Electric lock release (Fail locked, power required to un-lock)

1 x 12v dc power supply